• Products
    • Roppe
    • Centaur Floors
    • Six Degrees Flooring
    • Piper's Plank
    • Wedi
    • Floor Prep >
      • Uzin
      • Dependable Floor Prep
    • Tile Setting Materials >
      • Laticrete
      • Uzin Tile Setting
      • Bostick TruColor Grout
    • Van Gelder
    • Trims & Accessories >
      • Bengard / MD Pro
      • Diaplas
      • Seneca Millwork
      • Oak Mouldings
    • Tack Strip & Underlayment >
      • Traxx
    • Cushion >
      • Scottdel
      • Healthier Choice Cushion
      • Leggett & Platt Cushion
      • Carpenter Cushion
      • TredMOR (Sponge Cushion)
      • No Muv Padding
    • NuStair Resurfacing
    • Moisture Remediation >
      • Uzin MVR
      • Bone Dry Pro
      • Taylor Tools - Moisture Products
    • Floor Protection
    • DuPont StoneTech
    • Radiant Heating Systems >
      • Laticrete Strata Heat
      • Peel and Heat Cutting Edge
      • Prodesso Heat Membrane
      • Momento
    • Hardwood Refinishing Products >
      • Basic Coatings
      • DuraSeal
      • 3M Floor Sanding
      • Norton Abrasives
      • Woodwise Products
  • Adhesives
    • XL Adhesives
    • W.F. Taylor Adhesives
    • Divergent Adhesives
    • Parabond Adhesives
  • Tools
    • Carpet & Vinyl Tools >
      • Crain
      • Gundlach
      • D-Cut Products
      • Tego
      • Taylor Tools
      • Roberts
    • Ceramic Tile Tools >
      • Raimondi
      • Quick Pitch
      • Barwalt
      • Alpha Tools
      • Rubi Tools
      • QEP
    • Hardwood Tools >
      • Powernail
      • Bostich
      • Spotnail
      • Padco Applicators
    • Floor Welding Tools >
      • Wolff Tools
    • Surface Prep. Equipment >
      • Contec
      • Ceno Machines
      • Dustless Technologies
    • Trowels & Hand Tools >
      • Bullet Tools
      • Kraft Tools
      • Marshalltown
    • Specialty >
      • Wagner Rapid RH
      • National Equipment
    • Wolff Flooring Removal
    • Carpet Badger
    • Rental Equipment
  • Contact Us
    • Our People
  • Resources
  • Nextlite
AFS

Bone Dry Pro Specification Data

SECTION 07 16 00

CEMENTITIOUS & REACTIVE WATERPROOFING
(Crystalline Waterproofing)

PART 1 GENERAL

1.1 SECTION INCLUDES

  1. Permanent penetrating waterproofing that achieves utility through chemical reaction.
1.2 RELATED SECTIONS

Note to specifier: Add/ delete sections as required

  1. Section 03 30 00 - Cast-in-place Concrete
  2. Section 07 14 00 - Fluid Applied Waterproofing
  3. Section 09 00 00 - Finishes
  4. Section 09 90 00 - Paints and Coatings
1.3 REFERENCES

  1. ASTM E-96 - Standard Test Method for Water Vapor Transmission of Materials
  2. ASTM 1869- Standard test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride.
  3. ASTM F 2170- Standard Test Method for Determining Relative Humidity in Floor Slabs Using In Situ Probes
1.4 SUBMITTALS

  1. Submit under provisions of Section 01 33 00-Submittal Procedures
  2. Product Data: Manufacturer's data sheets on each product to be used, including:
    1. Preparation instructions, precautions and recommendations.
    2. Storage and handling requirements and recommendations.
    3. Installation methods.
  3. Manufacturer's instructions: Printed installation instructions for each product, including product storage requirements.
  4. Executed Warranties (when required)
1.5 QUALITY ASSURANCE

A. Regulatory requirements

  1. Product shall be free of Volatile Organic Compounds (VOC’s).
    Note to specifier: Delete 2 and 3 below if not applicable.
  2. Product shall be USDA chemically acceptable as a coating for application to structural surfaces where there is a possibility of incidental food contact in establishments operating under the Federal Meat and Poultry Products Inspection Program.
  3. Product shall be approved for use by The Regulatory Enforcement and Animal Care (REAC) division of the U.S. Dept. of Agriculture approved for use in all animal clinics and in holding and shelter facilities.
DELIVERY, STORAGE, AND HANDLING

B. Store products in original unopened containers until installation.

C. Maintain storage area conditions for products of this section in accordance with manufacturer's printed instructions until installation.

PART 2 PRODUCTS

2.1 MANUFACTURERS

  1. Acceptable Manufacturer: Bone Dry Pro by Bone Dry Products, Inc.
6520 67th Street, Kenosha, WI 53142 Tel: 262-694-9748
E-mail: [email protected]
Website: www.bonedryproducts.com

  1. Substitutions: Refer to Section 01 25 00 Substitution Procedures
2.2 MATERIALS

  1. Bone Dry Pro:
Clear, non-staining, waterborne silicate based penetrating sealer containing a blend of surfactants and enzyme catalysts.

PART 3 EXECUTION

Coverage area 900 square feet.

3.1 INSTALLATION

  1. Prepare and apply as per manufacturer’s specifications.
3.2 PREPARATION

  1. Clean surfaces to be treated removing impervious materials to allow sealer penetration.
  2. Hard troweled surfaces: Acid-etch or mechanically abrade to ensure proper product penetration.
3.3 APPLICATION

  1. Apply sealer in accordance with manufacturer’s published application instructions for indicated project conditions.
  2. Do not apply sealer to surfaces below 40 degrees F (4 degrees C) or above 90 degrees F (32 degrees C) unless recommended by the manufacturer.
  3. Do not apply sealer when rain is predicted within 24 hours or less than 48 hours after surface has been wet.
  4. Follow manufacturer’s recommendations for applying sealer in windy conditions or direct sunlight exposure.
3.4 WARRANTY (when required)

  1. Provide a warranty against failure due to incorrect application for a period of 10 years from the date of Substantial Completion.
  2. Provide the manufacturer's limited warranty against failure of sealer installation due to failure of sealer material for a period of 10 years from the date of Substantial Completion
©grw2012